SZ Stranding Line – Read Through This Article..

This automated visual Fiber tensile screening system is designed for operator skill impartial utilization in creation and laboratory configurations. Two fundamental design configurations enable the user to select between a set up for standard linear Proof testing and with additional mandrels for rotary higher power screening.

The linear version is ideal for production Proof testing with forces as much as 22 N. Motorized clamps with carefully developed rubber inserts be sure that the Optical Fiber Coloring Machine is not damaged in the testing process whilst at the same time getting rid of the requirement for an outside air supply. Levels of pulling force, tugging speed and hold time are programmable and conveniently offered to the operator from the built in LCD touch screen control. Data from assessments can be stored and accessed via the Universal serial bus port or Ethernet user interface.

Mandrels of the same design as with NYFORS’ optical Fiber recoaters can easily be installed on the Proof tester within the rotary higher power settings. The Fiber is covered across the two mandrels which support it with a special clamping mechanism. This way higher lots can be applied to the Fiber, allowing breaking power assessments below controlled conditions.

Changeable clamp placement facilitates testing with the highest force levels as well as screening of short Fiber measures. The compact and light weight design helps make the instrument easy to maneuver in a laboratory environment as well as integrate in a creation work table where space reaches reduced. The device is really a compact and lightweight tool ideal for testing the effectiveness of visual fibers approximately 30 N. The equipment is developed to meet all sorts of applications in which a strength check needs to be performed.

The device was created using the user in mind. The Secondary Coating Line is readily put into the guided linear clamps, and also the screening begins automatically with a “One Touch” go button. The built in microprocessor regulates all of the important guidelines such as tugging force, tugging speed and hold time. This enables to get a totally managed test each and every time.

The device can be linked to an external Computer, which enables usage of all programmable parameters and settings. The machine is adapted to stand-alone use or even to the integration into various subsystems. The device has an extensive capacity for signing and saving information like pulling force, tugging speed and Fiber diameter and other parameters.

Two recoat injector configurations can be purchased. The PTR307 uses an automated water pump to inject the recoat material. The quantity of materials dispensed from the automated injector is controlled by hand through the top-installed “Inject” button or programmed into the device making use of the tablet pc control. The PTR307B comes with a manual recoat shot system that requires the user to personally distribute the recoat material to the mold cavity; a replacement injector for that PTR307B recoater is available listed below. Make sure you note that this automatic injector is only compatible with high-directory recoat materials, while the handbook injector is compatible with both reduced- and high- index recoat material; both are sold separately listed below. Please contact Tech Assistance for more information.

he handbook injector can be installed to compatible Fiber recoaters via the 4-40 screws on the recoater real estate (see photo for the right). Use a 3/32″ hex key to safe the injector just before use. For connecting the PTRRRM towards the recoater mold, tighten the connector at the conclusion of the eco-friendly plastic material tubes, then release by way of a 1/4 turn to permit rotation.

The injector comes with a distribution valve as well as 2-position choice handle for directing the flow of recoat materials. A knurled dispensing screw with an internal plunger behaves as a syringe for the recoat materials. To fill up the syringe, point the handle downward (i.e., toward the recoat container), then spin the knurled dispensing attach counterclockwise until it spins easily to fill up the syringe (shown within the photo to the right). Then, to inject the recoat material into the mold, point the lever horizontally (i.e., dealing with qyjflh knurled attach) and spin the screw clockwise till nearby the end of the journey range is reached. Steer clear of bottoming out the dispenser as this may harm the internal plunger; also be careful when re-interesting the threads to prevent cross threading the dispensing attach. A number of fill/inject steps may be needed till air is displaced in the program. Use camera lens tissue plus an acetone or alcohol cleansing solution to accumulate FTTH Cable Production Line material that flows from your mold.

Leave a Reply

Your email address will not be published. Required fields are marked *